Ball Valves

Monday, May 7, 2012

LDR 020 7534 3/4-Inch Ball Hose Bibb Valve, Brass

LDR 020 7534 3/4-Inch Ball Hose Bibb Valve, Brass Review

LDR 020 7534 3/4-Inch Ball Hose Bibb Valve, Brass Feature

3/4-Inch IPS Brass
Quarter turn
No kink
100 percent Pressure tested at factory
CSA Approved

BALL VALVE TYPE HOSE BIBBS-MALE -

Saturday, May 5, 2012

Apollo 76-600 Stainless Steel Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/2" NPT Female

Apollo 76-600 Stainless Steel Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/2" NPT Female Review

Apollo 76-600 Stainless Steel Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/2" NPT Female Feature

Made of stainless steel for resistance to corrosion
Stainless steel lever handle with a vinyl sleeve for manual control
Three-port diverting valve to regulate flow among three sections of pipe
Pounds per square inch (gauge) (psig) rating of 800 for water, oil, and gas (WOG)
Female National Pipe Taper (NPT) threads for use with male threaded pipes

The Apollo 76-600 series two-piece three-port diverting ball valve is made of stainless steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel lever handle with a vinyl sleeve for manual control. The valve is three-port diverting to regulate flow among three sections of pipe. The maximum pressure is 800 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) and the valve has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage and this ball valve is standard (or regular) port for reduced valve size and cost. For use with water lines, processing plants, and agricultural applications, this valve meets standard NACE MR-01-75 for quality assurance in use in oil and gas applications.

Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications.

Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.

Thursday, May 3, 2012

Ball Drip Valve-1/2"x1/2" $8.28 ea for 10 or More

Ball Drip Valve-1/2"x1/2" .28 ea for 10 or More Review

Ball Drip Valve-1/2"x1/2" .28 ea for 10 or More Feature

Buy 10 or more get 40% off (.28 ea). Buy 150 or more get 50% off (.90 ea).
Automatic Ball Drip Valve 1/2"x1/2" . Used to drain low point of system between check valve & Fire Department connection
Automatically seals under pressure. Must be installed in horizontal position.
Standard Cast Brass Straight Connection NPT Both Sides
Used to drain low point of system between check valve & Fire Department connection

1/2"x1/2" Ball Drip Valve. Used to drain low point of system between check valve & Fire Department connection. Automatically seals under pressure.

Monday, April 30, 2012

Homewerks VBV-FSW-B5B Full Port Ball Valve with Drain, Female Thread x Female Thread, Brass, 1-Inch

Homewerks VBV-FSW-B5B Full Port Ball Valve with Drain, Female Thread x Female Thread, Brass, 1-Inch Review

Homewerks VBV-FSW-B5B Full Port Ball Valve with Drain, Female Thread x Female Thread, Brass, 1-Inch Feature

Full Port
500 PSI non-shock WOG
Forged brass body with Teflon seats
Drain waste and cap
Meets ANSI / NSF 61 low lead requirements

Homewerks VBV-FSW-B5B Full Port Ball Valve with Drain, Female Thread x Female Thread, Brass, 1-Inch.Full Port500 PSI non-shock WOGForged brass body with Teflon seatsDrain waste and capMeets ANSI / NSF 61 low lead requirements

Saturday, April 28, 2012

King Brothers Inc. BTU-0750-E 3/4-Inch Slip and Threaded PVC Heavy Duty True Union Ball Valve, Gray

King Brothers Inc. BTU-0750-E 3/4-Inch Slip and Threaded PVC Heavy Duty True Union Ball Valve, Gray Review

King Brothers Inc. BTU-0750-E 3/4-Inch Slip and Threaded PVC Heavy Duty True Union Ball Valve, Gray Feature

Made in the USA with quality PolyOne Schedule 80 PVC II material
NSF certified to be drinking water safe and low lead approved
UPC/IAPMO listed
Pressure rated to 235 psi at 73F Degree
Details and certifications available www.kbico.com

KBI | King Brothers Inc.

Thursday, April 26, 2012

LDR 020 7533 1/2-Inch Ball Hose Bibb Valve, Brass

LDR 020 7533 1/2-Inch Ball Hose Bibb Valve, Brass Review

LDR 020 7533 1/2-Inch Ball Hose Bibb Valve, Brass Feature

1/2-Inch IPS Brass
Quarter turn
100 percent Pressure tested at factory
CSA Approved